How Much Does Landscape Edging Cost Per Foot?
Landscape edging commonly costs about $4 to $20 per foot installed, depending on material, trenching, and site complexity. A weak quote can hide excavation, disposal, or corner work, then add those later. This guide shows what a per-foot edging bid includes, what it leaves out, and how to compare materials and site conditions. Cost ranges in this article align with common national pricing references for landscape edging, curb installation, and hardscape labor benchmarks from Homewyse, Angi, and Fixr.
Typical cost range
Most yard edging falls in a wide per-foot range because material choice and site conditions change the bid. A practical pricing hierarchy is: material-only pricing first, then installed pricing, then the full project total. For most edging jobs, material-only costs are lower than the installed total because labor, trenching, fastening, cleanup, and waste all add to the final quote. Common installed edging references place the market around $4 to $20 per linear foot, while curb and border pricing often clusters closer to $2 to $11.50 per linear foot for simpler materials and layouts. Sources: Homewyse landscape edging cost data; Angi landscape edging pricing; Fixr landscape edging cost guide.

So a quote may lean toward labor on a simple plastic border, or toward material on stone or poured concrete. The same 50 ft run can price very differently if it is straight, curved, or cut through hard soil. Regional labor rates also move the total up or down, and contractors may price access, disposal, and corner work separately. Sources: Homewyse cost breakdowns and labor factors; Angi pricing guidance.
Installed cost versus material-only cost
Start by separating material-only pricing from the installed total. Plastic or composite edging costs $0.50 to $3 per linear foot, while steel strip edging costs $1.50 to $5 per linear foot and aluminum strip edging costs $2 to $5 per linear foot. Brick or concrete paver border costs $2 to $5.50 per linear foot, poured concrete curb costs $3 to $8 per linear foot, and natural stone or cobble costs $12 to $18 per linear foot. These are material benchmarks, not complete installed quotes. Sources: Homewyse edging material and curb pricing; Fixr landscape edging cost ranges.
Installed pricing adds labor, trenching, layout, fastening, cleanup, and usually some waste. If a bid gives only one number, ask how much is material and how much is labor. Without that split, comparing one contractor with another gets messy fast. A fair comparison usually needs the same unit basis, the same run length, and the same assumptions for curves and grade changes. Sources: Homewyse installed edging cost breakdowns; Angi estimate guides.
Typical low, mid, and high ranges
The common project range is $630 to $1,710, and the national average cost is $1,170. Most curbing projects call for approximately 180 linear feet of edging materials, so a homeowner can use that size as a rough benchmark when reading a bid. Those figures work best as a full-project sanity check, not as a per-foot quote. Sources: Homewyse landscape edging cost averages and project totals.
A short bed border may stay near the low end. A full front yard perimeter with curves, gates, and driveway tie-ins often moves toward the middle or high end. The quoted price should rise when the installer must cut more pieces, stake more joints, or work around fixed features. A bid that is far below the benchmark range may be missing site prep, disposal, or finish work. Sources: Homewyse; Angi.
How regional pricing shifts the number
Labor rates vary by market, so the same edging material can cost more in one region than another. Soil type, disposal charges, travel time, and local contractor overhead also affect the final number. A quote that looks high in one city may be ordinary in another if labor is scarce or access is difficult. Sources: Homewyse regional cost variation notes; Fixr cost factors.
Compare bids on the same basis: linear feet, material type, trench depth, waste allowance, and cleanup. If one contractor quotes a lower price but excludes those items, the apparent savings can disappear fast. The cleanest comparison is an apples-to-apples installed price for the same footage and the same finish standard. Sources: Angi; Homewyse.
What drives edging labor cost
Labor usually makes up $1.50 to $10 per linear foot of a yard edging quote, but the final labor rate depends on layout and site conditions. Straight runs are faster than curves, and slopes, poor soil, roots, sprinklers, retaining walls, and utility conflicts all add time. That extra time shows up in the bid. Sources: Homewyse labor and install cost data; Angi labor-factor guidance.
Straight runs versus curves
Straight lines are the easiest and cheapest to install. Curves need more layout time, more cuts, and more care at each joint or stake point. The more the line bends, the more likely the installer needs shorter pieces, tighter spacing, and extra fitting time. That is why many quotes rise as the run becomes less geometric and more custom. Sources: Homewyse; Fixr.
A gentle curve may only add a little labor. Tight arcs around planting beds can add much more because the edging must follow the shape without gaps or kinks. That is one reason curved layouts often cost more per foot than a straight border. Sources: Homewyse landscape edging cost breakdowns.
Slopes, poor soil, and hidden utilities
Slopes slow the crew because the trench depth changes along the run and the edging must stay at a consistent reveal above grade. Rocky soil, clay, or compacted ground also takes longer to cut and backfill. If the line crosses roots, irrigation heads, or buried utilities, labor time rises again. Sources: Angi; Homewyse.
Sprinklers and utility conflicts can force rerouting. Retaining walls and hardscape edges can also change how the border is anchored. When a bid does not mention those issues, ask whether the contractor has priced them in or will add them later. Hidden obstacles are a common reason a low quote climbs after work starts. Sources: Homewyse; Fixr.
Trenching depth, stakes, and cleanup
Trenching depth affects both labor and material use. Deeper trenches take longer to dig and usually call for more backfill and more careful staking. Cleanup matters too. Some bids include spoil removal and final grading; others do not. Those exclusions can make a bid look cheaper than it really is. Sources: Homewyse installed edging scope details.
For steel strip edging, many products come in 8 or 10 foot lengths, so the bid should account for how many pieces, stakes, and connectors are needed. More joints mean more fit-up time, which is another labor add-on. This is especially important on curved runs where shorter segments and more connectors are often necessary. Sources: manufacturer product norms summarized in Homewyse and contractor pricing guides.
Edging quote table
This table is a bid-reading tool, not a fixed price list. It shows the parts of a per-foot quote that homeowners should separate before comparing bids. The totals are expected installed ranges, not promises. Use the formula row to translate a quote into a project total, then compare straight, curved, and sloped assumptions on the same footing.

| Material type | Material-only cost/ft | Labor cost/ft | Waste allowance | Trench depth assumption | Total expected installed cost/ft, straight runs | Total expected installed cost/ft, curves | Total expected installed cost/ft, slopes |
|---|---|---|---|---|---|---|---|
| Plastic or composite | $0.50 to $3 | $1.50 to $4 | 5% to 10% | 2 in to 4 in | $2.50 to $7 | $3.50 to $9 | $4.50 to $11 |
| Steel strip | $1.50 to $5 | $2 to $5 | 5% to 10% | 3 in to 5 in | $4 to $10 | $5.50 to $12.50 | $6.50 to $14 |
| Aluminum strip | $2 to $5 | $2.50 to $5 | 5% to 10% | 3 in to 5 in | $4.50 to $10 | $6 to $12.50 | $7 to $14 |
| Brick or concrete paver border | $2 to $5.50 | $3 to $6 | 8% to 12% | 4 in to 6 in | $5 to $11.50 | $7 to $14 | $8 to $16 |
| Poured concrete curb | $3 to $8 | $3 to $8 | 5% to 10% | 4 in to 6 in | $6 to $16 | $8 to $19 | $9 to $21 |
| Natural stone or cobble | $12 to $18 | $4 to $8 | 8% to 12% | 4 in to 6 in | $16 to $26 | $18 to $29 | $20 to $32 |
| Sample formula | Installed total = (material-only cost + labor cost) × linear feet × (1 + waste allowance). Example: 50 ft × ($2.50 material + $3 labor) × 1.10 = $302.50. | ||||||
| 25 ft example | Use this as a small-bed check: 25 ft × installed cost/ft = project total. A simple plastic run at $3.50/ft with 10% waste would be about $96.25 before any site-specific adders. | ||||||
| 50 ft example | Use this for a compact front-bed or short patio border: 50 ft × installed cost/ft = project total. A midrange metal run at $7/ft with 10% waste would be about $385 before special conditions. | ||||||
| 100 ft example | Use this for a larger border section: 100 ft × installed cost/ft = project total. A poured concrete run at $11/ft with 5% waste would be about $1,155 before any curve or slope premium. | ||||||
| 180 ft example | Use this as the full-project benchmark noted in the article: 180 ft × installed cost/ft = project total. At a market midpoint of about $6.50/ft, the project lands near $1,170, matching the national average. | ||||||
| Assumption note | Straight runs assume minimal layout complexity. Curved runs assume more cuts, more joints, and more fitting time. Sloped runs assume additional trench adjustment, backfill, and anchoring to keep the top reveal consistent. | ||||||
Which edging material costs the most?
Natural stone or cobble usually costs the most, with a material range of $12 to $18 per linear foot before labor. Poured concrete also sits near the upper end of the market at $3 to $8 per linear foot for material, while metal and plastic are usually lower cost choices. Stone and metal sit at the higher end of the overall $2 to $11.50 per linear foot curbing range. Sources: Homewyse; Fixr; Angi.
Plastic and metal
Plastic edging is the most budget-friendly option. It fits simple mulch beds, light gravel borders, and low-profile mower edges. Metal edging costs more than plastic, but it holds a cleaner line and often lasts longer under traffic and edge trimming. For homeowners comparing bids, plastic usually wins on initial cost while metal often wins on appearance and rigidity. Sources: Homewyse; Angi.
Metal edging usually comes in 8 or 10 foot lengths, which affects waste and connector count. More connectors and stake points mean more labor, but the material still remains cheaper than stone or poured concrete in many projects. That makes metal a common middle-ground option for clean borders without masonry pricing. Sources: contractor supply norms summarized in Homewyse; Fixr.
Wood and composite borders
Wood can price in the middle, but the quote should reflect treatment, thickness, and expected lifespan. Composite borders often sit near the lower to middle range, close to plastic pricing, depending on profile and brand. These products are often chosen when the homeowner wants a cleaner look than basic plastic without moving into masonry pricing.
Because product quality varies widely, the quote should specify thickness, profile, and whether fasteners or stakes are included. Otherwise, two bids may look similar while one uses a heavier-duty product and the other does not.
Brick, stone, and poured concrete
Brick or concrete paver border, natural stone, and poured concrete all add cost because they take more material handling and more careful setting. They also need better base preparation. A quote for these materials should list excavation, bedding, edge restraint, and joint treatment, or the price will be hard to compare. These are the materials most likely to push a project toward the upper end of the market. Sources: Homewyse; Fixr.
How much edging do you need?
Measure the perimeter in linear feet, then add waste for cuts, corners, and layout changes. For a simple run, total the straight sections along the edge of the bed or patio. For a curved shape, trace the outline and round up. Most projects also need a small cushion for overage. If the edging is being used to define a mulch bed, the perimeter around the planting area is the right number to measure, not the bed’s square footage. mulch beds often need extra footage at curves and corners because containment matters more than simple decoration.

Measuring perimeter in linear feet
Use a tape measure and measure each side separately. Add the sides together to get total linear feet. For a bed with four straight edges, sum all four edges. For a patio border, include each exposed side that will actually receive edging. If the border wraps around a mulch bed, measure the full containment line so the bid reflects the actual run that must be installed.
Do not measure area in square feet. Edging is bought and quoted by line, not by surface area. If the line changes direction, count every segment and every return. That is especially important for curved beds, because the installer needs the perimeter length, not the garden bed’s square footage.
Adding waste and extra cuts
Waste allowance covers cuts, small fitting errors, and breakage. Plastic may need a smaller allowance than stone or pavers, while masonry borders often need more. Curves and corners usually increase waste because the installer cannot always use every offcut. The tighter the layout, the more important it is to build waste into the quote instead of treating it as an afterthought.
Suppose a bed measures 62 ft around and the bid includes a 10% waste allowance. The order should cover about 68 ft total. That extra 6 ft helps cover cuts and fit adjustments. On a larger project, the same percentage can add a meaningful amount to the final invoice, so it should be visible in the estimate.
Example project sizes for beds and patios
A small front bed might need 25 ft to 40 ft. A midsize backyard border may land around 80 ft to 120 ft. Most curbing projects run 180 linear feet of edging materials, so a full-yard bid often lands well above a simple patio border. That 180-foot benchmark is a useful reality check for a full-property quote.
Picture a 40-foot flower bed that needs edging along one long curve and two short ends. That is 40 ft of perimeter before waste. If the layout includes two curves and a slope, the final bid should be higher than a straight, level run of the same length. The same footage can produce very different totals once installation complexity is added. Sources: Homewyse; Angi.
How deep and tall should edging be?
A practical edging bid should account for both bury depth and the top reveal above finish grade. The edging must be tall enough to hold mulch or gravel in place, but not so high that it creates a trip hazard or looks exposed. The right height depends on the material and the job. In other words, depth and reveal should be priced as part of function, not treated as optional details.
Bury depth and top reveal
Most edging needs part of its height buried and part left above grade. That buried portion helps hold the line. The visible portion, or reveal, should be enough to contain mulch or gravel and create a mower edge without becoming a toe catch.
Ask whether the quote assumes a standard trench depth or a deeper cut. A deeper trench can improve retention, but it takes more labor and may require more material. If the bid ignores this, the final install may fall short on either function or finish. The reveal target should be stated clearly so the final look matches the intended use. Sources: Homewyse; Angi.
Mower edge and containment function
Edging does three basic jobs: it holds gravel or mulch, prevents material escape, and creates a mower edge. If the border is for mulch beds, the reveal can be modest. If it is for gravel containment, the quote should reflect a stronger profile and tighter installation. The right profile depends on whether the goal is separation, containment, or a crisp mowing line.
A border around a lawn edge may only need a clean line. A gravel edge along a path needs better containment and more careful staking. The use case matters because it changes how much edge height and depth the installer needs. A decorative strip and a functional containment border are not the same job. Sources: Homewyse; Fixr.
Trip-hazard limits and finish grade
Any visible edge above finish grade should stay low enough to avoid a toe catch and high enough to do its job. Loose bricks, high stone tops, or uneven poured concrete can create a trip hazard if the finish grade changes later. The bid should state the final reveal target.
If the project borders a walkway, driveway, or patio, ask how the top will sit relative to the finished surface. A flush or nearly flush edge is often safer where people step across the line. This matters most when the edging crosses pedestrian paths or meets hardscape transitions.
What should a quote include?
A complete edging quote should list the material, the linear footage, the labor rate, trenching depth, stake count, connectors, joints, waste allowance, and cleanup. If the bid leaves those out, the owner may be comparing incomplete numbers. Ask for the full scope in writing before signing. A quote that names only a per-foot price is not enough if it omits the details that drive the final total. Sources: Homewyse; Angi.
Connectors, stakes, and joints
Connection details matter. Overlaps, connectors, and joint gaps change both labor and material use. Metal edging often needs stakes at regular intervals, and some products need connectors at each seam. A quote should say whether those items are included or billed separately.
For a straight plastic run, the contractor may need fewer joints and fewer cuts. For a curved layout, the same quote may need more connectors or tighter stake spacing to keep the line from shifting. That difference is one of the biggest reasons two bids can look similar while not actually covering the same work.
Base prep, excavation, and backfill
Base prep can include stripping sod, cutting a trench, leveling the bed edge, placing the edging, and backfilling. On masonry borders, it may also include bedding material or concrete support. These steps take time and should appear in the bid if they are part of the job.
If a contractor says the price is “installed,” ask what installed means. Does it include excavation? Disposal? Regrading? Cleanup? Those details often explain why two per-foot quotes do not match. Installed should mean the border is ready for use, not that the base work is still pending. Sources: Homewyse; Fixr.
What to ask before you sign
- How many linear feet are included?
- What material and thickness are being quoted?
- Does the price include trenching, stakes, connectors, and cleanup?
- What waste allowance is built into the total?
- How are curves, slopes, roots, and utility conflicts priced?
- What is the final top reveal above finish grade?
A common mistake is focusing only on the per-foot quote and overlooking whether the price includes corners, stakes, and removal of old edging. Suppose two bids both say $8 per foot. If one includes trenching, connectors, and disposal while the other does not, the lower number is not the better deal. Compare the scope first, then the price.
Frequently asked questions
How much does concrete edging cost?
Concrete edging usually costs more than plastic and often lands in the middle-to-upper part of the market. A practical installed benchmark is roughly $6 to $16 per foot for poured concrete curb when labor is included, depending on soil, layout, and finish requirements. That makes concrete a durable but not budget-priced choice. Sources: Homewyse; Fixr.
How much does concrete edging cost per foot?
For concrete edging, a practical installed expectation is usually above the material-only number because excavation, setting, and finishing add labor. Poured concrete curb costs $3 to $8 per linear foot for material, so a full installed quote often lands above that base once labor is included. Curves and slopes push it higher. Sources: Homewyse.
What is the average cost of edging per linear foot?
A broad average lands near the center of the market, but the safest benchmark is the full curbing range of $2 to $11.50 per linear foot. Those numbers are best used together: per-foot range for quick comparison, and project totals for a sanity check. Sources: Homewyse.
How much labor is included in edging cost?
Professional installation typically costs $1.50 to $10 per linear foot, but that labor share can rise when the job has curves, slopes, poor soil, roots, sprinklers, retaining walls, or utility conflicts. Ask whether the bid includes trenching, staking, cleanup, and joint work. If not, the quote is incomplete. Sources: Homewyse; Angi.
What factors make edging cost more?
Curves, slopes, hard soil, buried utilities, root cutting, and masonry materials all raise the price. Waste allowance also matters when the layout has many corners or cut pieces. A quote should show those adders instead of hiding them in a single lump sum. If the project requires more fitting, the installed price should reflect that. Sources: Homewyse; Fixr.
Is plastic edging cheaper than concrete or stone?
Yes. Plastic or composite edging costs $0.50 to $3 per linear foot, which is far below natural stone or cobble at $12 to $18 per linear foot and usually below poured concrete at $3 to $8 per linear foot. Plastic is the most budget-friendly option, especially for simple mulch beds and straight runs. Sources: Homewyse; Fixr.
How do curved or sloped layouts affect edging cost?
Curves and slopes both increase labor, and curves also increase waste. Tight bends need more fitting time and more joints, while slopes change trench depth and backfill work. A straight, level border is usually the cheapest run to install. The more the line departs from a simple layout, the more the price should rise. Sources: Homewyse; Angi.
How do I estimate edging cost for my yard?
Measure the total linear feet, choose the material, add a waste allowance, then add labor based on site difficulty. Use the quote table as a benchmark. For a simple yard border, compare bids by material, trench depth, and whether cleanup and connectors are included. That approach gives a cleaner estimate than relying on one lump sum. Sources: Homewyse; Angi.
How much edging do I need for a patio or bed?
Measure every side that needs a border and add them together. A small patio edge may need 25 ft to 40 ft, while a medium bed may need 80 ft or more. Most curbing projects use about 180 linear feet, which helps frame larger yard estimates. Add waste if the layout includes curves or many cuts. Sources: Homewyse.
What size project can I expect from a typical edging estimate?
That size is common for a full border package, not a tiny accent strip. Smaller beds and short patio edges usually price below that range. Use the 180-foot benchmark to test whether a bid is undersized, oversized, or simply missing scope. Sources: Homewyse.