How Deep Should Landscape Edging Be Installed?
Install edging about 4–6 in. deep for mulch and grass control, and about 6–8 in. deep for gravel or paver borders, with about 1/2–1 in. of edge left above grade. Too shallow, and grass creeps through, mulch washes out, and gravel leaks. Set the depth to the use, the reveal, and the stake pattern for that border.
Trench depth, reveal, and stake spacing by use case
Start with the use case, not the material. A mulch border can stay shallower than a restraint that must hold gravel or lock pavers in place. Trench depth, visible reveal, and stake spacing all change with the load the edging has to resist. For setup, choose edging sized for the bed and use landscape edging that matches the border’s job.

For most lawn-to-bed borders, a 6-inch trench is a common starting point, and the top edge usually sits about 1/2 inch above finished grade. Manufacturer guidance for edging products commonly calls for a small reveal, not a tall curb, so the border can still be trimmed cleanly without catching mower wheels.
What you’ll need
- Edging material and stakes
- Shovel, spade, and measuring tape
- Level, string line, and marking paint
- Compaction tool and backfill material
Recommended edging depth by use case
| Application | Typical trench depth | Above-grade reveal | Stake spacing | Common failure risk | Best for / not ideal when |
|---|---|---|---|---|---|
| Grass-mulch borders | 4–6 in. | 1/2–1 in. | About 2 ft. on straight runs; closer on curves | Shallow trench lets roots and sod creep under the edge | Best for simple bed lines; not ideal when root pressure is heavy or soil stays soft |
| Steel edging | 5–6 in. | 1/2–1 in. | Extra stakes at joints and bends | Thin metal shifts if it is not pinned firmly | Best for crisp curves and straight lines; not ideal when clay soils swell and shrink a lot |
| Plastic edging | 4–6 in. | 1/2–1 in. | Closer spacing than steel, especially on curves | Flexible strip bows, twists, or pops loose | Best for light-duty bed borders; not ideal when stronger lateral load or frost movement is expected |
| Paver restraint | 6–8 in. | Low enough for the soldier course to sit level | Every 2 ft. at minimum | Edge fails if the pavers are not fully supported | Best for hardscape edges; not ideal when the base is thin or curves need tighter stake spacing |
| Gravel containment | 6–8 in. | At least 1 in. above the gravel surface | Closer spacing where gravel pushes outward | Stone spills over a low edge and migrates into turf | Best for edging that must hold loose aggregate; not ideal when the border is too low or soil is loose |
When to go deeper: Frost-prone soils, wet clay, and beds with strong root pressure need more anchoring, not just more visible height. Extension guidance on frost heave and soil shrink-swell generally points to deeper trenches within product limits, longer stakes, tighter stake spacing, and well-compacted backfill rather than trying to reach full frost depth with every edging type.
- Mark the border with paint or string line.
- Dig the trench to the target depth for the application.
- Set the edging so the top sits at the planned reveal.
- Drive stakes at a 45-degree angle, leaving 2 in. undriven.
- Space stakes tighter on curves and at every joint.
- Backfill in lifts and compact the soil against the edge.
- Recheck height after tamping, then adjust by 1/2 in. if needed.
How deep should metal landscape edging go?
Metal edging usually works best with a 5–6 in. trench and a 1/2–1 in. reveal above finished grade. Steel products are commonly installed with a modest reveal and firm staking, according to manufacturer instructions for metal edging systems. That keeps the top edge useful without creating a tall lip.

Steel is a good choice for curves because it stays straighter than thin plastic when it is anchored well. Install guides for steel edging typically emphasize tight staking, especially on bends and at joints, because movement starts where the line changes direction.
Anchoring thin steel for mower-safe edges
Steel edging needs stake support more than depth alone. Use extra stakes at joints and bends, and keep the run tight to the string line before backfilling. A common setup is one stake every 2 ft., with closer spacing on tight radii and at transitions. Manufacturer instructions often call for more support on curves than on straight runs.
A 20 ft. steel border with two inside curves and one splice needs more fastening at the curve points and at the splice than it does in the straight middle section. The goal is to resist lateral shift while still leaving a small, mower-safe reveal.
How deep should plastic landscape edging be installed?
Plastic edging is usually installed 4–6 in. deep, but depth alone does not make it stable. The material is thinner and more flexible than steel, so it depends on stake support to resist bowing, twisting, and lift from settling or frost movement. Manufacturer install guides for plastic edging commonly call for frequent staking, especially on curves.
That limitation matters most in freeze-thaw climates. Shallow plastic edging often fails first at the stake holes, corners, and joints, where the strip can work loose as the soil expands and contracts. If the bed edge also has heavy foot traffic or gravel load, plastic is usually a maintenance border, not a structural restraint.
Where freeze-thaw damage shows up first
Look for lifted sections, wavy tops, and gaps at the splice points. Those are signs the trench is too shallow, the soil is loose, or the stakes are too far apart. Extra staking helps, but it cannot turn thin plastic into a curb. In clay soils, wetting and drying can also push edging out of line.
How deep should paver edging be installed?
Paver edging should usually go 6–8 in. deep, because it is holding a hard edge instead of just trimming a bed line. It needs a prepared sub-base, a level seat for the restraint, and a height that lets the soldier course sit flush rather than rocking on the border. ICPI-style paver restraint guidance emphasizes support, alignment, and edge restraint as part of the paving system.

Use paver restraint where the edging is part of the hardscape, not just a visual trim. That means the edge must resist lateral movement from the paving units, base settlement, and sweeping or freeze-thaw forces.
When edging is restraint, not a lawn border
A paver edge holds lateral movement. It is part of the paving assembly, so shallow install depth or loose backfill can lead to spreading joints and a drifting border. For that reason, the restraint needs closer alignment checks than a simple mulch edge, especially where curves demand tighter stake spacing.
A common first-timer mistake is setting plastic landscape edging flush with the soil surface instead of burying it deep enough to hold mulch and stop roots from pushing it out. If the course rises above the restraint or the restraint sits too high, the pavers can sit proud and the line becomes hard to sweep and harder to keep level.
Common mistakes
Most edging failures come from depth, height, and spacing being out of balance. The border may look straight on day one, but shallow trenching, weak staking, and poor compaction let it move over time. Soil behavior matters too: expansive clay, root pressure, and frost heave can all amplify small install errors.
- Installing too shallow for the material. Thin plastic and loose gravel need more support than a simple bed edge.
- Leaving the reveal too low or too high. Too low hides the edge and weakens bed definition; too high creates mower strikes and a visible trip point.
- Using too few stakes on curves and joints. Movement starts where the line bends or where two pieces meet.
- Skipping compaction and backfill. Loose soil lets the edge shift, lean, or heave after rain and freeze-thaw cycles.
Picture a 30 ft. mulch border in clay soil with only a few stakes. It may hold for one season, then bulge where the soil swells and the curve relaxes. The fix is deeper set, tighter stake spacing, and firmer backfill, not a taller reveal.
Frequently asked questions
How deep should landscape edging be installed?
A practical range is 4–6 in. for grass and mulch borders, and 6–8 in. for gravel or paver restraint. The visible edge should usually sit about 1/2–1 in. above finished grade so it stays readable and still gives mower clearance.
How deep should metal landscape edging go below grade?
Most metal edging performs well at about 5–6 in. below grade, with a small reveal above the soil. Steel also needs firm staking at joints and bends. On curves, the edge usually stays truer when the stake pattern is tighter than on straight runs.
How deep should edging be for gravel containment?
For gravel, use about 6–8 in. of trench depth and keep at least 1 in. of edging above the gravel surface. That extra height helps hold stone in place. Where gravel pushes hard against the border, closer stake spacing reduces spillout.
Does landscape edging need to go below the frost line?
Usually no, but frost-prone soils need deeper anchoring than mild climates. The goal is to resist heave, not necessarily to reach full frost depth. University and extension resources on frost heave generally recommend deeper trenches within product limits, longer stakes, tighter spacing, and compacted backfill instead of assuming a full frost-line set will solve movement.
How many stakes should landscape edging use?
A common target is about 2 ft. apart on straight runs, with extra stakes at corners, joints, and curves. Paver restraint needs at least that spacing, and often more support where the border carries lateral load. If the line wavers, add stakes before backfilling fully.